jupiter is converted and its OSD rebuilt, so the capacity constraint that took
immich down is gone with all three nodes back.
cephfs-metadata deliberately stays at size 2 / min_size 1. It has to be
degraded again for saturn and then neptune, and each transition re-replicates
the pool, so toggling it per node buys nothing but churn. Its comment said to
restore it once k8s-1 was back, which is now misleading about the plan; it
restores after the last conversion instead.
The immich comments lose their jupiter-specific framing — taking both
Deployments down is a pre-flight step for any single-node maintenance now, and
the runbook carries it.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
jupiter is back as a bare-metal Talos node, so its OSD returns to the storage
fleet on the new drive.
The device is named by /dev/disk/by-id rather than by bare device name, because
the bare name would be wrong here. Talos enumerates this machine's three NVMe
drives in a different order than Proxmox did, and nvme0n1 on k8s-1 is the
Kingston system disk:
nvme0n1 50026B7382B48B86 Kingston Talos system disk
nvme1n1 2332E86B749A Crucial Talos EPHEMERAL (/var)
nvme2n1 S437NX0M400426 PM983 this OSD
Rook would most likely have declined the system disk for carrying partitions,
but relying on that is luck rather than intent. The by-id path derives from
model and serial and does not depend on enumeration order.
k8s-2 and k8s-3 keep bare names: each guest sees exactly one block device,
the drive passed through from its host, so there is nothing to disambiguate.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
The first install of this node came up with no address on any interface and had
to be recovered from the console. This is the configuration that replaced it,
now running on jupiter.
The alias layer was the cause, but not for the reason it first appeared. Reading
the v1.12.6 source: aliases ARE supported as VLAN parents — link_config.go
resolves parent links through the alias map, and the field's own doc comment
says so. The structure was fine. What is not fine is the failure behaviour.
LinkAliasConfigController skips a selector that matches zero links with no log
of any kind, contradicting the doc comment on the type which claims an error is
returned. And permanent_addr comes from the ETHTOOL_GPERMADDR ioctl with no
fallback to the current address, so a driver that does not answer it yields an
empty string, an unmatched glob, and silence.
That alone would have been survivable. What made it total is that Talos stops
running default DHCP operators for the WHOLE machine as soon as a single
new-style link, VLAN or DHCP document exists — the gate is presence of a
document, not success of resolution. So the silent miss removed the only
configured path while the safety net was already disabled. There is no fail-open
option.
Aliases are worth having and should come back. The condition is that they are
verified rather than assumed: apply with `--mode=try`, which rolls back on its
own, and check that linkaliasspec exists and that permanentAddr is actually
populated before trusting it. A LinkConfig on the real kernel name alongside the
alias resolves regardless of whether the alias landed, and costs nothing.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Three NVMe drives are present, not two: the Crucial stays in the machine as
EPHEMERAL rather than being pulled.
The second I226 is enp90s0, not enp89s0. Adding that third drive renumbered
the PCI buses and renamed it, which is a concrete demonstration of why every
NIC in this file is matched by permanent MAC rather than by name or bus path.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
The Crucial P3 that was this node's Ceph OSD stays in the machine rather than
being pulled, and takes over /var. At 87% of rated endurance it is finished as
an OSD, but everything EPHEMERAL holds — containerd images and snapshots, pod
logs, the Ceph mon store — is reconstructible, so the drive is consumable in
that role.
It also removes the constraint that keeps biting elsewhere: /var becomes
~931 GB instead of the 64 GB the VM-era zvol gave it. k8s-3 tripped
DiskPressure twice today the moment it absorbed another node's pods, with
image GC already at its floor and ~20 GB of unreclaimable overlayfs snapshots.
This node will not have that problem, and the same treatment is available to
saturn and neptune when they convert.
Talos only honours volume configuration when the volume does not yet exist, so
this must ship in the first apply-config; applied later it is silently ignored
and relocating EPHEMERAL then needs a disk wipe and a boot from install media.
The selector matches an exact serial. There are three NVMe drives in this
machine now and `disk.transport == 'nvme' && !system_disk` would match the
PM983 as well, which would hand Talos the OSD drive.
Verified with talosctl validate --mode metal against v1.12.6.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
With one of three nodes out for the bare-metal conversion, the remaining pair
cannot hold the workload: cluster CPU requests exceed two nodes' capacity by
roughly 200m once DaemonSets and unplaceable Ceph pods are discounted, and
k8s-3 sits ~5.8 GiB above the kubelet's eviction threshold with image GC
already at its floor.
immich is the right thing to stop rather than squeeze. machine-learning
reserves 500m against a 2m idle draw, but inference bursts hard, so cutting
its request would misrepresent what it needs the moment someone uploads
photos. Stopping it removes the reservation honestly, and takes its pods and
image pulls off k8s-3 for the duration.
The Postgres cluster stays up, so recovery is these two replica counts and
nothing else.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
useAllNodes makes it impossible to retire an OSD ahead of pulling its drive.
Purging osd.2 and deleting its deployment held for one reconcile: the operator
saw a node it was told to use, carrying a device with a BlueStore signature,
and rebuilt the OSD. Ceph then began backfilling onto the very drive being
replaced.
Listing nodes explicitly makes membership of the storage fleet a property of
this file rather than of which nodes happen to exist, so a node can be removed
before its disk is touched.
k8s-1 is out while jupiter's OSD is swapped for the PM983 and the node is
converted to bare metal. The cluster runs on two OSDs until it is re-added;
all pools are size 2 / min_size 1 and stay fully redundant across the pair.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Draining k8s-1 for the jupiter conversion left three pods unschedulable:
k8s-2 and k8s-3 both sat at 100% of requested CPU while actually using 21-23%.
Cluster-wide the gap is 19,680m requested against 7,957m used.
crowdsec is the clearest single contributor. The chart defaults reserve 500m
for each agent and for the LAPI; measured draw is 1-2m. As a DaemonSet the
agent alone parks half a core on every node. Nothing here had ever set
resources, so this was an inherited default rather than a decision.
Only the request changes. Limits stay at the chart default, so a log flood can
still burst to 500m; what shrinks is the reservation the scheduler subtracts
from every node whether or not the process uses it.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
jupiter's Crucial P3 Plus OSD is at 87% endurance used, and reaching the
MS-01's only U.2-capable slot means moving the boot drive anyway. Doing the
bare-metal conversion in the same window avoids opening the machine twice and
throws away no work: the osd-ssd PCI mapping that a Proxmox-side swap would
need to be re-pointed at ceases to exist.
Networking uses the v1.12 multi-document config rather than the deprecated
machine.network.interfaces. The docs do not define what happens when one link
is configured by both schemas, so k8s-1 keeps every link in one of them. This
also buys VLANConfig.name, which is free-form: naming the VLAN 30 link ens19
keeps the four v30iot macvlan NADs working unchanged across VM and bare-metal
nodes, so the cluster can stay mixed without pinning those workloads.
Physical NICs are matched by permanent MAC, not driver — both X710 ports bind
i40e here, unlike the single passed-through port k8s-2/k8s-3 see.
cephfs-metadata drops to size 2 / min_size 1 for the duration. At size 3 on
two remaining hosts every PG sits undersized with min_size 2, so one further
OSD loss would block IO on every CephFS mount cluster-wide. This must go back
to size 3 once k8s-1 rejoins.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
The sweep restores every discovered Velero schedule, immich's ~180 GiB
library included. At size 2 that is ~360 GiB raw, ~120 GiB per OSD, and
measured on 2026-08-25 it was ~350 of the ~740 GB each drive wrote per
week — ~47% of the endurance budget, against a ~65 GB/day weekday
baseline.
That baseline is itself the result of the 2026-08-18..21 write-reduction
work (#518, #519, #520, CNPG checkpoint tuning, RAM-backed emptyDirs,
paperless data to RBD, CI workspaces to cephfs-ci), which cut per-drive
writes ~70% from ~195 GB/day. With the application tier down, the restore
test is now the single largest consumer of remaining QLC endurance; the
three OSD drives are at 81/82/87% used.
Monthly still exercises every restore path and cuts the sweep's share of
drive wear ~4x, moving per-drive weekly writes from ~740 GB to ~530 GB.
Cadence-only change:
- 0 8 * * 0 -> 0 8 1 * *, keeping the 08:00 UTC slot that clears the
03:15-07:15 daily backup window (see the comment in the manifest).
- ttlSecondsAfterFinished 14 d -> 40 d, so the previous run is still
inspectable when the next one fires.
- Comments and docs that state the cadence updated to match, including
the BLUESTORE_SLOW_OP_ALERT runbook text, which tells the reader to
check whether a stall fell inside the restore-test window.
No day-of-week form is available: Kubernetes parses cron with
robfig/cron's standard parser, whose day-of-week field allows only
`* / , - ?` (no Quartz `#` nth-weekday), and restricting both day fields
ORs them.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
The Wetterstation now carries a non-default reporting configuration: min
interval 5s on all ten reportable attributes, and tighter reportable-change
deadbands on temperature, humidity and pressure. None of it is expressible
in configuration.yaml - Zigbee2MQTT has no settings-schema field for
reporting configuration - so it lives only on the device and in Z2M's
database.db. This documents it and how to restore it.
min was 10s against an 8.8s transmit interval. Since min is a hold-off, every
change-triggered report was held past a transmit cycle and landed on the
next, so attributes reported at best every 17.6s and drifted out of phase.
The published stream showed no 8.8s periodicity at all. At min 5 each
attribute reports on its own transmit and the stream carries one publish per
cycle, measured at a mean gap of 8.69s. Publish volume fell from ~631/h to
~445/h because each publish is now a whole cycle rather than a fragment.
The deadbands come from the shared modernExtend helpers, which the WS90
definition composes without overrides. They are anti-chatter values sized for
battery-powered indoor sensors. Temperature was 1.00 C, giving a staircase
that moved about twice an hour; it is now 0.1 C, matching the resolution the
device actually reports. Pressure was 5 kPa - 50 hPa, which real barometric
pressure never traverses, so it only ever updated on the hourly heartbeat
that pressure_trend and weather_condition derive from. Note the same library
configures the identical ZCL attribute with a 5 hPa deadband in its older
reporting.ts helper, so the two code paths disagree by 10x.
Anything that makes Z2M re-run configure on the device reverts all of it, and
a fresh PVC will not have it. The restore commands are written out literally
rather than generated by a shell helper, because the nested quoting through
`kubectl exec -- sh -c` is where this goes wrong; each was executed and
verified as written, including the read-back, and re-applying is a no-op.
No behaviour change from this commit itself - the device was reconfigured at
runtime, this only records it.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
#560 claimed a merged episode "surfaces as a single all-zero frame". It
does not, and the difference decides whether a downstream filter is even
possible.
The zeros propagate attribute by attribute through the burst, so the
merged frame carries whatever subset had zeroed when that burst ended.
Across three episodes captured at nanosecond resolution the propagation
happened to complete, which is where the wrong generalisation came from.
Nothing guarantees it. A burst ending mid-propagation publishes a frame
with temperature at zero while humidity and pressure still read normally,
which is a physically consistent measurement - Z2M recomputes dew_point
from the false temperature - and is not separable from a genuine winter
reading.
The zeros also begin inside an otherwise normal transmit cycle, roughly
20ms after a valid reading in the same burst (measured: 27.7ms, 19.8ms,
22.0ms). They occupy a regular reporting slot, so no timing property
distinguishes them either.
Since the merge is last-wins and the zeros arrive at the tail of the
burst, it resolves that burst to the zeros and discards the valid reading
that led it. So debounce trades six bad samples per episode for one, at
the cost of one good sample. That is a bound on the corruption, not a
filter, and the comment now says so.
No behaviour change; the debounce value and device stanza are untouched.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
The value is unchanged and correct; the comment committed alongside it in
#559 was neither accurate nor the right place for most of what it said.
Accuracy. It cited the device's ZCL reporting configuration as the bound,
reading minRepIntval 10 as "the station updates every 10s". minRepIntval
is not a cadence: with maxRepIntval 3600 and a reportable change set, the
ZCL reporting model gives periodic reports at the MAXIMUM interval — once
an hour — plus change-driven reports each held back so it lands no sooner
than 10s after the previous. It is a hold-off on change-triggered reports
and says nothing about the gap between reports of different attributes,
which is what a debounce window sees.
The bound that applies is the documented transmit interval — readings
every 2s, transmitted every 8.8s — against Z2M's documented rule not to
set debounce above the sensor's update interval. Shelly's knowledge base
rounds the same figure to 9s.
It also claimed the window had to exceed 1s because "the recovery burst
straddles a second boundary", inferred from log lines stamped 11:42:11
and 11:42:12. Those are second-resolution timestamps and cannot
distinguish 10ms from 900ms. No lower bound was ever established.
Length. The rest was commit-message material sitting in a config file:
justification for the chosen value, gap-distribution and run-length
measurements, and notes reconciling my own earlier misreadings. Comments
state facts about the system, not the history of arriving at them. What
remains is what the device does, what debounce does to it, and the
constraint on the value — 41 lines down to 13.
Verified before writing: post-debounce frames arrive complete (all 22
fields, no partials) at a settled ~10s cadence.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Two changes to the Wetterstation (Ecowitt WS90, 0xc02cedfffe958f40), both
aimed at the station's recurring zero-drop glitch.
2.13.0 carries zigbee-herdsman-converters#12748, which discards the ZCL
non-value markers (0xffff / 0xff / 0xffffff) the WS90 emits when a reading
is unavailable. Without it those markers are scaled and published as
measurements — the 6553 m/s gust readings in Koenkk/zigbee2mqtt#31048. The
release also recovers the rain rate after a counter reset, which is the
same lifetime-counter dip that packages/wetterstation.yaml compensates for
on the Home Assistant side. Its only breaking change is dropping Node.js 20
for bare-metal installs; the container ships its own runtime. The amd64
manifest was verified pullable before this commit.
debounce: 2 addresses the part 2.13.0 does not fix. Koenkk/zigbee2mqtt#31048
is still open, and the author of #12748 states explicitly that it does not
cover the zero drops: "a zero can be a real reading for these attributes,
only the all-bits-set markers are provably invalid."
The station reports as a burst of seven per-cluster ZCL frames and Z2M
publishes its full cumulative state once per frame, so one device report
becomes seven MQTT messages. During a glitch the zeros appear progressively
across those seven, which is what makes the corruption unrecognisable
downstream: an intermediate frame carrying {"temperature":0,"humidity":92,
"pressure":96.9} is internally consistent (Z2M recomputes dew_point from the
false temperature) and cannot be told apart from a legitimate winter
reading. Merging the burst yields a single frame with the all-zero
signature, which a consumer can reject.
The window is bounded on both sides. Above: the device's own reporting
configuration sets minRepIntval 10 / maxRepIntval 3600 on all seven WS90
clusters (1024/1026/1027/1029 and 0xfc01/0xfc02/0xfc03), so no attribute
repeats inside 10s. Below: the recovery burst straddles a second boundary,
so 1s splits it and emits a partial frame.
Staggering was checked rather than assumed — the 10s floor is per attribute,
and nine attributes report across those clusters, so a trailing-edge timer
could in principle keep resetting and never flush. Over 6h the longest
unbroken chain of sub-2s gaps was 5, bounding worst-case deferral under
~10s.
The device is also absent from the seeded device list, which predates it
joining, so this adds the friendly_name too.
NOTE: this file is seed-only. A running Z2M owns its configuration.yaml on
the PVC, so this does not change the live instance — it only makes a fresh
PVC come up correctly. debounce is requiresRestart, so applying it live
needs the option set on the running instance and a restart; the image bump
supplies the restart.
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
From the #426 audit. Tag verified present before bumping.
The kaniko bump that was originally in this branch is dropped. It would
have pinned a new `-debug` image, and debug variants are not to run in
the production cluster. kaniko is archived upstream, so the fix is
migration rather than a version bump; tracked in #552 along with the
`-debug` requirement.
Comments should say what the setting does and what constrains it. The
blocks added in #542, #544, #545 and #547 had grown into incident
write-ups: measurement runs, prior values, how a problem was found,
what a check used to be. That belongs in commit messages and the wiki,
both of which already carry it.
Trimmed, no behaviour change:
cephcluster.yaml 22 lines -> 6 (cephx rotation)
cephfs-ci.yaml 26 lines -> 7 (why size 2)
prometheusrule-ceph.yaml (CephHealthWarn, 43 -> 13;
CephPoolLostRedundancy, 15 -> 7)
The operative facts are kept: which checks are excluded and why they
cannot clear, that POOL_NO_REDUNDANCY reports blocked maintenance and
not only data risk, and that size 1 needs dedicated OSDs.
The unreplicated CI pools introduced in #542 make every OSD on the
cluster permanently un-restartable.
`ceph osd ok-to-stop` refuses while stopping an OSD would take PGs
offline. A size-1 pool puts every PG on exactly one OSD, so the check
fails for all three:
Error EBUSY: unsafe to stop osd(s) at this time
(20 PGs are or would become offline)
bad_become_inactive: 13.6 13.9 ... 14.1c 14.1d
Pools 13 and 14 are cephfs-ci-metadata and cephfs-ci-data0. The size-2
pools are not implicated — they run min_size 1 and appear under
ok_become_degraded, which is allowed.
Rook gates OSD restarts on that check, so this blocks CephX key
rotation, Ceph upgrades, node drains and reboots, and drive
replacement. It surfaced when #545 deadlocked: Rook retried
ok-to-stop against all three OSDs several times a second and could
never succeed, while `ceph -s` reported 217 pgs active+clean
throughout. Nothing is unhealthy; the restarts are simply refused.
The reasoning in #542 was that unreplicated CI data only risks
in-flight pipelines, since every byte is a fresh git clone. That part
holds. What it missed is that the cost is not scoped to the pool: one
unreplicated pool freezes maintenance for the entire cluster.
Most of #542's saving came from keeping CI churn off `cephfs`, whose
metadataPool is size 3 — that survives this change. Only the second-
order gain from dropping the replica is given up, and cephfs-ci-data0
stores 0 B with cephfs-ci-metadata at 182 MiB, so the backfill is
trivial.
size 1 becomes viable again once these pools sit on OSDs of their own,
where the permanently un-stoppable OSD holds nothing but throwaway
data. That is planned with the retired QLC drives.
Alerting follows the same change:
- POOL_NO_REDUNDANCY is no longer excluded from CephHealthWarn. It was
excluded because cephfs-ci was expected to keep it permanently
active; no pool is unreplicated now, so the exclusion would only
hide a real one losing its replicas.
- CephPoolLostRedundancy drops its cephfs-ci exemption for the same
reason, and its description now states the maintenance consequence,
not just the data-loss one.
- The AUTH_INSECURE_* exclusion is reworded. Calling it
"known-accepted" reads as a decision that the risk is fine; it is a
kernel-blocked remediation (aes256k over the CSI mount path needs
kernel 7.0+, nodes run 6.18).
Refs #542, #545, #527
Ceph v19.2.6 ships the fix for CVE-2025-30156, a CephX authentication
bypass: AES-128-CBC service tickets carry no HMAC and use a hard-coded
IV, so a holder of any low-privilege key can bit-flip a ticket into
cluster-admin in linear time. Upgrading the binaries does not resolve
it — the keys themselves must be rotated to the aes256k cipher.
The cluster is mid-procedure. auth_allowed_ciphers (aes, aes256k),
auth_preferred_cipher (aes256k) and auth_service_cipher (aes256k) are
already set, and the rotating service keys were wiped, but no actual
key rotation has happened: every entity in status.cephx is still
keyGeneration 1 with keyType aes, created under 19.2.3.
Rook automates daemon-key rotation but it is opt-in and defaults to
Disabled, so spec.security.cephx was left empty and nothing rotated.
Rook v1.20.6 and Ceph v19.2.6 are both past the version floor the
feature requires.
Rotating daemon keys clears AUTH_INSECURE_SERVICE_KEY_TYPE, the only
one of the six new checks at ERR severity. That is the operationally
urgent part: Rook skips CephFS and RGW reconciliation entirely while
health is HEALTH_ERR — which is what deadlocked the mds/rgw rollout in
issue #527 — and the check is presently held down only by a mon-side
mute with a finite TTL. When that mute lapses the cluster returns to
HEALTH_ERR and the reconcile freeze comes back.
CSI keys are deliberately left on aes. aes256k over the CSI mount path
requires a host kernel of 7.0 or newer and these nodes run 6.18, so
`aes` must stay in auth_allowed_ciphers for CSI to authenticate at all.
AUTH_INSECURE_CLIENT_KEY_TYPE, AUTH_INSECURE_KEYS_ALLOWED and
AUTH_INSECURE_KEYS_CREATABLE therefore stay raised at WARN until the
nodes run a kernel that supports it.
Rotation restarts most Ceph daemons. With size 2 pools across 3 OSDs
this should be applied deliberately rather than alongside other churn,
and Ceph should reach HEALTH_OK before anything else touches the
cluster.
Refs #527, #528
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
CephHealthWarn alerted on `ceph_health_status == 1`. It has been FIRING since
at least 2026-08-21T00:26Z and cannot clear: four AUTH_INSECURE_* checks are
permanently active from CVE-2025-30156 (#527) and stay that way until Rook
>=1.20.5 lands. A permanently-firing alert reports nothing -- every Ceph
warning since then has been invisible behind it.
This is a pre-existing gap, not a consequence of the cephfs-ci work, though
that work would have added a second permanent cause (POOL_NO_REDUNDANCY, since
the CI pools are size 1 on purpose).
ceph_health_detail exposes each check as its own series, so the alert now fires
on any check that is NOT known-accepted, and names it. Verified against live
data: 5 checks active, 0 unexpected, so it is quiet now and fires the moment
something genuinely new appears.
Excluding POOL_NO_REDUNDANCY wholesale would give something up: that check is
cluster-wide and does not say WHICH pool, so accepting it for cephfs-ci would
equally hide a production pool dropping to one replica. CephPoolLostRedundancy
restores that. There is no pool-size metric, but bytes_used/stored IS the
replication factor -- verified live as replicapool 2, cephfs-data0 2,
cephfs-metadata 3, cephfs-ci-metadata 1.
Both alerts were tested against live data before committing, in BOTH
directions. The positive control matters as much as the negative one: an early
draft used a >1e9 floor which silently excluded the CI pools entirely, so the
expression could not have matched anything. It looked correct precisely because
it returned no results. The control caught it; the floor is now 1e6.
The floor is not what suppresses the near-empty rgw pools. Their ratios are
9-36 because per-object overhead dominates, so they never match `< 1.5`.
6h on CephHealthWarn is unchanged -- Ceph warns for self-clearing conditions
and paging on those trains people to ignore the alert.
Repoints WOODPECKER_BACKEND_K8S_STORAGE_CLASS at ceph-filesystem-ci, the
dedicated filesystem added in #542 whose pools are both size 1.
Measured 2026-08-21, polling both CephFS pools every 15s:
CI active 1.5 min (6 intervals): data0 143.2 MB metadata 17.2 MB
CI idle 16.0 min (63 intervals): data0 0.0 MB metadata 11.0 MB
CI share of writes: data0 100%, metadata 61%
data0 takes zero bytes across 16 minutes without a pipeline, so its entire
write volume is CI. The 15s cadence is what made this visible: a pipeline
creates, uses and deletes its PVC inside ~2 minutes, so a 5-minute sample
reported no CI pods during bursts CI was causing.
Per pipeline this moves the drive cost from 71.6x2 + 8.2x3 = ~168 MB to
~80 MB, since neither pool is replicated on the new filesystem.
RWX is unchanged and still required: pipeline steps share the workspace PVC
and the k8s backend can schedule them on different nodes, so an RWO volume
fails to mount on the second node. Only the filesystem underneath changes.
Also corrects the justification written into #542 for leaving
ceph-filesystem-ephemeral alone. That commit claimed restore-test.sh handles
"REAL data which must not land on unreplicated pools". That is wrong: its
probe PVCs are as throwaway as a CI workspace -- the authoritative copy is the
backup on Hetzner, and losing a probe just means re-running the test.
The actual reason it cannot move is technical: those probes are snapshot
CLONES, and `ceph fs subvolume snapshot clone` operates within a single
filesystem, so a snapshot taken in `cephfs` cannot be cloned into `cephfs-ci`.
Landing them unreplicated would require a second size-1 data pool inside
`cephfs`; restore-test runs weekly against CI's ~96 pipelines/day, so that is
not worth the complexity.
cephfs-ci verified healthy before this change: PHASE Ready, MDS Running, both
pools reporting size 1.
Woodpecker's Kubernetes backend creates a PVC per pipeline, fills it with a
checkout plus build output, and deletes it when the pipeline ends. Those
workspaces currently live on the shared `cephfs`, so throwaway data is
replicated as if it mattered: 2x in cephfs-data0 and 3x in cephfs-metadata.
Measured 2026-08-21 by polling both pools every 15s. The interval matters --
at 5 minutes a whole pipeline is invisible, because its PVC is created, used
and deleted inside ~2 minutes. Sampling that slowly reported zero CI pods
during bursts CI was causing, which sent this investigation down three wrong
paths before the cadence was fixed.
one pipeline, a single 15s interval: data0 +71.6 MB metadata +8.2 MB
every interval with no CI pod: data0 ~0 metadata ~0
So CI accounts for essentially all CephFS write volume; between pipelines the
metadata pool is quiet at ~4 MB/day. On the shared filesystem one pipeline
costs 71.6x2 + 8.2x3 = ~168 MB of drive writes. On this one it costs ~80 MB.
size 1 is correct here even though it was rejected for `cephfs`. There,
metadataPool stays at 3 because losing it destroys the entire filesystem
rather than the objects on one OSD, and 550 GiB of real data depends on it.
Here every byte is a fresh git clone: total loss means in-flight pipelines
fail and get re-run. Replicating throwaway data was the cost, so it is what
gets removed.
`ceph-filesystem-ephemeral` is deliberately NOT repointed. It has a second
consumer -- velero/restore-test.sh restores REAL data through it for
verification, which must not land on unreplicated pools. A new class also
sidesteps StorageClass.parameters being immutable.
Nothing uses ceph-filesystem-ci yet, so this commit is inert: it provisions
the filesystem and its MDS and changes no existing workload. Repointing the
Woodpecker agent is a separate change, once this is confirmed healthy.
Known consequence: size 1 raises POOL_NO_REDUNDANCY, so cluster health will
warn until that is addressed. Silencing it via mon_warn_on_pool_no_redundancy
is cluster-wide and would also hide a production pool dropping to 1, so it
wants a targeted alert instead -- deliberately left out of this commit rather
than switching the warning off blind.
The MDS is 512Mi/1Gi with no standby, not the 4Gi active+standby that `cephfs`
runs. That figure is driven by immich's cached inode count; a CI workspace is
a few thousand files that vanish with the pipeline, and a second daemon to
protect throwaway work is not worth its memory.
A WAL segment is a fixed 16 MiB file. archive_timeout forces a switch on a
timer, and the switched-out segment is written and archived at its full size
no matter how little real WAL it holds. CNPG defaults to 5min, permitting
288 segments/day per cluster of largely padding.
gf-pg went first as a staged rollout and is now verified: 211 -> 41 MB/hour,
an 81% cut, with archived segments falling from ~12/hour to ~1.5/hour in
step. Two independent signals moving together is what confirms the volume
was padding rather than data, and the measured result matched the ~35
MB/hour predicted beforehand.
Fleet-wide this is worth roughly 18 GB/day of logical writes, which at
size=2 with ~1.27x BlueStore overhead is ~45 GB/day at the drives -- about
14% of the 328 GB/day the three OSD NVMes currently take.
ak-pg gets 15min rather than 30min. It holds credentials, sessions and
enrolment state, and the extra 15min would save only a further 0.3 GB/day,
which does not justify doubling the worst-case loss window on that data.
ha-pg saves least in relative terms: its segments are already 63% full of
real WAL (4.9 GB/day), so the timer is not what drives most of its switches.
Also corrects two comments in ha-pg-cluster.yaml that this work falsified.
wal_compression: the claim that these clusters "were not getting compression"
was wrong -- "on" is pglz, which was already compressing. Switching to zstd
moved the WAL rate not at all (4911/4976 -> 5002 MB/day, by LSN advance over
20min windows). Full-page images genuinely are ~62% of WAL here (61.9%
measured as a steady-state delta, against 62.4% lifetime -- so the migration
did not skew it, which was my first guess and it was wrong). There was simply
no headroom between pglz and zstd on this data. zstd is kept because it is
not worse and costs nothing, but it is not a lever.
checkpoint_timeout: 15min -> 30min likewise did not move WAL. Probable reason
is that a recorder is append-mostly -- a page is dirtied while it fills and
then not touched again, so it pays its full-page image once whatever the
checkpoint interval. Kept, but flagged as unjustified pending a data-file
measurement: this volume takes ~11 GB/day against 4.9 GB/day of WAL, so most
of its traffic is outside what a WAL measurement can see.
Context: drive-endurance work on three QLC NVMe OSDs at 81-87% wear.
A WAL segment is a fixed 16 MiB file. archive_timeout forces a segment
switch on a timer so the archive never trails reality by more than that
interval, and the switched-out segment is written and archived at its full
16 MiB no matter how few bytes of real WAL it holds. CNPG defaults this to
5min, which permits up to 288 segments/day = 4.6 GB/day per cluster.
Measured on gf-pg: the database is 21 MB and generates 4.5 MB/day of actual
WAL, while its RBD volume takes 211 MB/hour -- against 192 MB/hour predicted
from 12 switches of 16 MiB. Essentially every byte written to this volume is
padding, roughly 1100x amplification.
This resolves an anomaly that has been open since the start of the endurance
work: gf-pg appeared to write gigabytes per day for a 21 MB database, and
neither WAL volume nor data changes could account for it. Segment padding
does, exactly.
Applied to gf-pg alone as a staged rollout. It is the lowest-risk cluster
and gives the cleanest signal -- its real WAL is small enough that any change
in volume is unambiguously attributable to this parameter. The same default
affects all seven clusters and is worth an estimated ~24 GB/day of logical
writes fleet-wide, but that only goes ahead once this one is verified.
The cost is RPO. On total loss of the cluster, up to 30min of Grafana state
becomes unrecoverable instead of 5min. That state is dashboards, annotations
and preferences, changing at ~4.5 MB/day, so the window is nearly always
empty. Clusters holding credentials or job state get evaluated separately
rather than inheriting this value by default.
archive_timeout is in CNPG's GlobalDefaultSettings, not its
FixedConfigurationParameters, so it is user-overridable -- verified against
pkg/postgres/configuration.go rather than assumed.
Context: drive-endurance work on three QLC NVMe OSDs at 81-87% wear.
`wal_compression: "on"` resolves to pglz, PostgreSQL's original 2016-era
algorithm. Every CNPG cluster here was set that way, so none of them were
getting the compression actually available to them: all seven builds accept
lz4 and zstd (verified via pg_settings.enumvals on each, including immich's
custom pgvector image and trmnl's PostgreSQL 18).
This matters because of what dominates recorder-style write volume. A page
is written to WAL in full -- all 8 KiB -- on its first modification after a
checkpoint, for torn-page protection. Measured on ha-pg, those full-page
images are 62.4% of WAL bytes. Compressing them is therefore the single
largest lever available on WAL volume, and pglz was the weakest option for
the job.
ha-pg additionally moves checkpoint_timeout 15min -> 30min. Full-page images
are emitted once per page per checkpoint interval, so doubling the interval
roughly halves how often each hot page pays the 8 KiB toll. max_wal_size
stays at 2GB deliberately: it must remain well above what one interval
generates, or checkpoints would trigger on size and the interval change
would do nothing. Recovery replays at most one interval of WAL -- under
200MB at the measured rate, i.e. seconds.
The other six clusters keep checkpoint_timeout at 15min. Their measured
write rates do not justify trading recovery time: gf-pg generates 4.5 MB/day
of WAL and wp-pg 62 MB/day, against ak-pg's 604 MB/day.
full_page_writes stays on everywhere. Disabling it would remove the
overhead entirely but RBD can tear a page across an object boundary, and
the trade is write volume against an unrecoverable database.
Both parameters are sighup-reloadable, so this does not restart any cluster.
Context: drive-endurance work on three QLC NVMe OSDs at 81-87% wear.
Prometheus held 298,236 active series. ~108,000 of them -- over a third -- were
apiserver/etcd `_bucket` histograms. Each fans out to one series per bucket x
verb x resource x scope, so a single metric was 23,810 series on its own. Every
Home Assistant metric combined is ~4,100 for comparison.
That cardinality is the dominant driver of Prometheus write volume (~11 GB/day of
TSDB + WAL, doubled again by Ceph replication) and none of it is observable value
on three nodes: per-bucket apiserver latency quantiles are for clusters with SLAs
and dozens of nodes.
Dropped, all verified to have ZERO rule dependencies by checking each metric
against the live alert and recording rules:
apiserver_request_duration_seconds_bucket rules=0 23,810 series
apiserver_request_body_size_bytes_bucket rules=0 23,200
etcd_request_duration_seconds_bucket rules=0 15,840
apiserver_watch_list_duration_seconds_bucket rules=0 11,538
apiserver_watch_cache_read_wait_seconds_bucket rules=0 8,232
apiserver_response_sizes_bucket rules=0 7,592
apiserver_watch_events_sizes_bucket rules=0 5,220
-------
95,432
KEPT deliberately: apiserver_request_sli_duration_seconds_bucket (12,144 series).
23 recording rules depend on it, including the apiserver availability SLO and the
KubeAPIErrorBudgetBurn burn-rate series. Dropping it would silently break that
alerting -- the manifest says so inline, so a later "tidy up" of the regex does
not remove it by accident.
Only `_bucket` series are dropped. The matching `_count` and `_sum` remain, so
request rates and mean latencies still work; what is lost is per-bucket
quantiles.
etcd_* is included even though kubeEtcd is disabled: those are the apiserver's
own etcd-client metrics on the apiserver endpoint, not a separate etcd scrape.
Expected: ~32% fewer active series, so roughly 11 -> 7 GB/day of Prometheus
writes, ~8 GB/day off the drives once replication is counted. Will verify against
prometheus_tsdb_head_series rather than assume.
Refs #434
Co-Authored-By: Claude Bot <noreply@anthropic.com>
An image reference is not a secret. Encoding it as base64 `data` had two real
costs: no reviewer sees a version change in a diff, and no $imagepolicy marker
can attach to a base64 blob.
The result was a two-minor version skew in the component that performs every
base backup and WAL archive for seven Postgres clusters (#535):
controller plugin-barman-cloud:v0.14.0 <- auto-bumped by Flux
sidecar plugin-barman-cloud-sidecar:v0.12.0 <- invisible, never moved
Not stale pods: ha-pg-1 was created hours ago during the recorder migration and
still received v0.12.0.
Three changes:
1. The Secret now uses stringData with the tag in plaintext, carrying an
$imagepolicy marker. The Secret KIND is kept because the controller reads it
via secretKeyRef; switching to a ConfigMap would need a matching edit to that
reference and diverge further from upstream. stringData is accepted
identically by the API server.
2. ImageRepository + ImagePolicy added for the sidecar image, with the same
filter and 0.x range as the controller, so the two cannot drift apart again.
Only the controller was tracked before.
3. Tag aligned to v0.14.0 to match the controller.
The Secret name carries a kustomize hash suffix from upstream's secretGenerator
but is static here, so editing the value does not change the name and the
deployment's secretKeyRef stays valid — verified in the render, which still shows
the name twice (Secret + reference).
Verified the tag EXISTS before pinning it: pulling
plugin-barman-cloud-sidecar:v0.14.0 succeeds (the pod fails later on a missing
`true` binary in that minimal image, which is the container command, not the
pull). Pinning a non-existent tag would have put all seven Postgres clusters into
ImagePullBackOff.
EXPECTED IMPACT: bumping the sidecar changes every Postgres pod spec, so all
seven CNPG clusters roll. CNPG handles this as a normal rolling restart. Backups
should be confirmed working afterwards — 113 Backup CRs exist today, newest ~3h
old and completed.
Note for future re-imports: upstream ships this Secret as base64 `data` with no
marker, so a wholesale re-import silently reintroduces the skew. The manifest now
says so inline.
Refs #535
Co-Authored-By: Claude Bot <noreply@anthropic.com>
Switches the Deployment's `data` volume from paperless-data (RWX,
ceph-filesystem) to paperless-data-block (RWO, ceph-block). `consume` and `media`
stay on CephFS -- the ftp-scanner writes to those from another node, so they
genuinely need RWX.
The copy is already done and verified byte-for-byte with paperless stopped:
src files: 75
dst files: 75
IDENTICAL: name, size and mtime match for every file
index segments: src 3, dst 3
mtime parity matters specifically because the Whoosh index segments carry their
own consistency expectations; `cp -a` preserved them. (The "can't preserve" lines
in the copy log were for the mount root /dst/. itself, not the files.)
Why: only this Deployment ever mounted the volume, and its contents are
single-writer state. Being on CephFS meant every access crossed the MDS --
measured with zero CI running, 22 requests/sec sustained and ~15 journal
events/sec against 2 directory commits per 180s, i.e. cap/inode churn rather
than file writes. That accounted for most of the constant 7-8 GB/day on
cephfs-metadata, which is a size 3 pool.
cephfs-metadata stays at size 3 deliberately: losing it destroys the entire
filesystem rather than the objects on one OSD, and the 275 GiB in cephfs-data0
depends on it.
paperless-data is retained (prune: disabled) as the rollback. It must NOT be
deleted until search has been confirmed returning results -- that is what proves
the index survived, not merely that paperless starts.
Refs #434
Co-Authored-By: Claude Bot <noreply@anthropic.com>
paperless-data is declared ReadWriteMany on ceph-filesystem, but only ONE pod
mounts it -- the paperless Deployment itself. Its contents are all single-writer
state: the 50 MB Whoosh index, classification_model.pickle,
celerybeat-schedule.db, log/, migration_lock. 75 files, nothing shared. Only
`consume` and `media` genuinely need RWX, because the ftp-scanner writes to those
from another node.
It is on CephFS by default, not by requirement, and every access goes through the
MDS. Measured 2026-08-20 with ZERO CI pipelines running:
paperless-data client request_load_avg 22 (all other sessions 0-1)
MDS over 180s 4,052 client requests = 22.5/s
2,718 journal events = 15/s
2 dir commits <- not file writes
Cap and inode churn from repeated access, not data being written. That accounts
for most of the constant 7-8 GB/day on cephfs-metadata, and since that pool is
size 3, roughly 21-24 GB/day reaches the drives.
cephfs-metadata deliberately STAYS at size 3. Losing it destroys the whole
filesystem rather than the objects on one OSD, and the 275 GiB in cephfs-data0
rides on it. Cutting writes at source is the fix; cutting replication is not.
PHASE 1 ONLY, and inert: the PVC is created empty and nothing mounts it. The data
copy and the deployment repoint are separate steps, documented in
MIGRATION-data-to-block.md along with why the copy needs paperless stopped (the
Whoosh index and celerybeat schedule are both live-written, so copying under an
active writer gives a torn read).
Honest sizing: ~21-24 GB/day off the drives against ~432 GB/day cluster-wide, so
about 5%. This is a correctness fix -- a single-writer volume does not belong on
a shared filesystem -- more than a large win. It also removes 22 req/sec of MDS
load, which benefits Woodpecker CI workspaces sharing the same MDS.
Refs #434
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Ten Postgres instances across seven CNPG clusters are ~48 GB/day of the
cluster's ~114 GB/day of client writes, and only ha-pg carried any
write-reduction tuning. The rest ran Postgres defaults, which favour throughput
over storage that wears out.
MEASURED, not assumed. ak-pg since 2026-05-17:
checkpoints_timed 27,624 = 291/day, i.e. one every 5 min (the default)
buffers_checkpoint 25,801,628 = ~206 GB flushed
database size 1,046 MB
That is the whole database rewritten roughly twice a day. The pathology is
specific to idle databases: sessions, tokens and job state re-dirty the same few
pages constantly, and checkpoint_timeout=5min forces each of them to disk 288
times a day instead of letting them coalesce. At 15min they are written a third
as often.
max_wal_size is raised alongside it. Without that, checkpoints trigger on size
instead and the timeout change does nothing. It also bounds crash recovery to at
most 2GB of WAL replay.
Applied to ak-pg, pprl-pg, tr-pg, wp-pg, im-pg, gf-pg. ha-pg already had it.
synchronous_commit is deliberately NOT changed here. It is off for ha-pg because
a state recorder is telemetry; these clusters hold credentials, documents and job
state, where losing the last few hundred ms of commits on an unclean shutdown is
not an acceptable trade for write volume.
Separately, ha-pg shared_buffers 256MB -> 512MB. After 15h on Postgres its
buffers_backend was 629,704 of 939,025 total page writes -- 67% written by
backends rather than the checkpointer or bgwriter, which means the working set
does not fit in the buffer pool and pages are written out repeatedly instead of
coalescing. Memory limit raised 1Gi -> 1536Mi to keep the same headroom (measured
383Mi in use, of which 256MB was shared_buffers).
Verified before commit by rendering every cluster and asserting the tuning landed
under spec.postgresql.parameters with the barman plugin block untouched. That
check exists because the first attempt at this matched the wrong `parameters:`
key -- the barman plugin's, at 6-space indent under plugins: -- and corrupted
wp-pg's barmanObjectName. Reverted and redone with an indent-aware match.
Refs #434
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
The renderer was the single largest writer in the cluster -- more than every
Ceph OSD and every database combined -- and none of it needed to touch disk.
Measured 2026-08-20 from the container's own cgroup io.stat:
253:0 (node /dev/vda5) 249,092,697,088 bytes over 7.3 days = ~34 GB/day
252:48 (its own PVC) 340 MB total = negligible
So the writes were not going to its volume at all; they were going to the
node's filesystem via a disk-backed emptyDir. `emptyDir: {}` without
`medium: Memory` is node storage, which is easy to read as "ephemeral, so
free".
The cause is cadence rather than volume. schedules.template.json renders on
"* * * * *", so Chrome is launched 1440 times a day and each launch creates,
fills and deletes a /tmp/puppeteer_dev_chrome_profile-* directory. At rest /tmp
holds under 8 MB -- it is pure churn for data that never outlives the render.
tmpfs pages count against the container's memory limit, so the 512Mi cap is
kept deliberately: measured usage is 129Mi against a 2Gi limit, leaving ample
headroom even if the cap were fully consumed.
Expected effect: ~34 GB/day off the OS disks, which measured 215 GB/day over a
4h window. This is a bigger cluster-wide reduction than the Home Assistant
recorder migration achieved, for a one-line change.
Refs #434
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Seven Postgres clusters back up to Hetzner and nothing alerted if that stopped.
The only related rule was HetznerBackupEndpointDown, which probes the S3
endpoint — it proves the bucket is reachable, not that anything was written to
it. Same failure shape as the WordPress backup that failed nightly for three
days against a bucket declared in tofu but never applied: the status surface
looked fine because nothing checked the thing that mattered.
CNPGWalArchiveBacklog is the load-bearing rule. `ready` counts WAL segments
waiting in pg_wal/archive_status; steady state is 0 on every cluster. A
sustained backlog means the archiver is failing, so point-in-time recovery is
silently broken from that moment and pg_wal grows until it fills the PVC and
takes Postgres down. Threshold >5 sustained for 30m: a segment is 16 MiB, so
that is ~80 MiB of un-archived WAL — well below anything that threatens the
volume, far above idle noise. It reads only the instance-level collector, so it
works despite #522.
CNPGBackupFailed fires on a base backup failure within 24h, guarded on
timestamp > 0 so the epoch-zero default is not read as "failed in 1970".
DELIBERATELY NOT ADDED: the backup-age alert, which is the one you would most
want. `(time() - cnpg_collector_last_available_backup_timestamp) > 48h` cannot
be used today because that metric reads exactly 0 on every instance in the
cluster (verified across gf-pg, ak-pg-1/2, pprl-pg-2/3, im-pg, wp-pg, ha-pg).
CNPG has no record of any successful backup anywhere, because the Backup CRs it
derives that from are deleted within a minute of completing — #522. Adding it
now would fire permanently for all seven clusters and be silenced within a day,
which is worse than not having it.
The backups themselves DO work; verified independently by listing the bucket
with barman-cloud-backup-list and restoring a WAL segment back out of S3. The
gap is in the record, not the data.
Both expressions were validated against live Prometheus before commit rather
than written from the metric names: the WAL selector matches 8 real series (a
zero match would mean a dead rule, the defect fixed in
prometheusrule-woodpecker-rotation.yaml), and neither expression fires
currently, which is correct since archiving is healthy and the only recorded
backup failure is ~91 days old.
Refs #522
Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
2026-08-19 15:43:07 +02:00
43 changed files with 1335 additions and 166 deletions
description:"The Ceph cluster has held HEALTH_WARN for six hours, so it is not a self-clearing blip. Get the detail with `kubectl -n rook-ceph exec deploy/rook-ceph-tools -- ceph health detail`."
summary:"Ceph health check {{ $labels.name }} active for 6h"
description:"Ceph health check {{ $labels.name }} has been active for six hours. Only AUTH_INSECURE_* is excluded (kernel-blocked, see #527). BLUESTORE_SLOW_OP_ALERT is sticky for 24h after the last stall and clears itself: check whether the stall fell inside the monthly Velero restore-test window (08:00-14:00Z on the 1st), which is expected on these QLC drives — one outside that window, or a repeat on the same OSD, means check that drive (#557). Detail: `kubectl -n rook-ceph exec deploy/rook-ceph-tools -- ceph health detail`."
- alert:CephPoolLostRedundancy
# Names the pool, which POOL_NO_REDUNDANCY does not.
#
# There is no pool-size metric, but bytes_used/stored IS the
# replication factor. The >1e6 floor drops pools too small to measure
# meaningfully, empty ones included.
#
# No pool is exempt.
expr:|
ceph_pool_bytes_used / ceph_pool_stored < 1.5 and ceph_pool_stored > 1e6
for:30m
labels:
severity:critical
annotations:
summary:"Ceph pool {{ $labels.pool_id }} is running unreplicated"
description:"Pool {{ $labels.pool_id }} has a replication factor below 1.5, meaning a single OSD loss destroys data. No pool is meant to be unreplicated — an unreplicated pool also blocks ALL OSD maintenance cluster-wide, since `ceph osd ok-to-stop` refuses while its PGs would go offline. Check with `kubectl -n rook-ceph exec deploy/rook-ceph-tools -- ceph osd pool ls detail`."
- alert:CephHealthError
# HEALTH_ERR means data availability or redundancy is at risk.
summary:"CNPG WAL archiving is falling behind on {{ $labels.namespace }}/{{ $labels.pod }}"
description:"{{ $value }} WAL segments have been waiting to archive for over 30 minutes. Point-in-time recovery is broken for anything after the last archived segment, and pg_wal will grow until the PVC fills. Check the barman-cloud sidecar logs and the ObjectStore credentials: `kubectl -n {{ $labels.namespace }} logs {{ $labels.pod }} -c plugin-barman-cloud`."
- alert:CNPGBackupFailed
# cnpg_collector_last_failed_backup_timestamp is a unix timestamp, 0
# when no failure is recorded. Guard on > 0 so the epoch-zero default
summary:"CNPG backup failed in the last 24h on {{ $labels.namespace }}/{{ $labels.pod }}"
description:"A base backup for {{ $labels.namespace }}/{{ $labels.pod }} failed within the last 24 hours. Verify what is actually in the bucket rather than trusting CR status — see the barman-cloud-backup-list recipe in kubernetes/apps/home-assistant/MIGRATION-recorder-postgres.md."
# DELIBERATELY ABSENT: a backup-age alert, which is the one you would
summary:"WordPress MariaDB backup has not succeeded in 26h+"
description:"The wordpress-mariadb-backup CronJob's last successful run is over 26 hours old. Check the newest Job's pod logs in the wordpress namespace: `kubectl -n wordpress get jobs`. The 2026-08-19 failure was `The specified bucket does not exist.` against renner-uno-k8s-mariadb while the endpoint itself probed healthy, so a green HetznerBackupEndpointDown does not clear this."
- alert:WordpressMariadbBackupNeverRan
# The staleness expression above goes blind when the metric is
# absent, which is what happens once the operator recreates the
# CronJob. Without this guard "never backed up" is quieter than
summary:"WordPress MariaDB backup has no recorded successful run"
description:"The wordpress-mariadb-backup CronJob exists but has no lastSuccessfulTime: either it has not completed once since the Backup CR was recreated, or every run since has failed. Check `kubectl -n wordpress get jobs` and that the hetzner-s3-creds ExternalSecret is synced."
# Second NIC on v30iot so Cilium L2 announce can win ARP on the IoT
# VLAN from this node (previously only k8s-edge had v30iot, so any
# IoT-pool LB lease landing here was unreachable from devices).
extra_network_bridges=["v30iot"]
disks=[
{
storage="local-zfs"
size="64G"
format="raw"
slot="virtio0"
file_id=local.talos_image
}
]
hostpci=[
{
mapping="osd-ssd"
},
{
mapping="x710-port1"
}
]
tags="kubernetes;talos;controlplane"
ssh_public_keys=local.common_ssh_keys
vm_state="running"
# Rebuild pipeline issues `-replace`; skip graceful shutdown so a
# non-responsive Talos guest can't hang the destroy for 30 minutes.
stop_on_destroy=true
}
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
claude-botandClaude Opus 5
k.renner
security-bot
issue-fix-bot